Ultrasonic Cleaner For Cleaning Industrial Metal Filter
Application: Electronic factory, Car work shops, Industrial and mining area, Laboratories, Hospitals, Dental clinics, Watch shop, Optical shops, Jewelry shops,Mobile phone repair shoos, and household use.
Thanks for purchase OURS ultrasonic cleaner, please read the instruction manual carefully before operation to avoid damage to the machine or any danger to personal safety, And please keep it for reference.
Ensure the power supply is in rated range before power cable is connected. Refitting is strictly prohibited! Attention thst the control panel will be eroded by organic solution, strong acid and strong alkali.
Ensure the earth wiring is well connected before starting.
Ensure the power key or knob is on the "OFF" place beforr starting.
Do not operate if the tank is empty, or ultrasonic transducer will be damaged. If heating is needed, the water level shouldn't be less than 2/3.
Please colse the lid to reduce noise and pay sttention to water and steam in case of burning skin while open the lid.
Do not relocate the machine when the fluid in the tank in case of overflow.
Please choose suitable model or basket based on cleaning objects.
OKS series standard ultrasonic cleaner suggest using water-soluble liquid. Strong acid or flammability cleaner is forbidden.Heater is forbidden if use volatile solvent-base cleaning agent. Machine is recommended rest period of time(usually more than 3 minutes)after work 30 minutes.
Do not use the machine in severe environment:
The place where temperature changes fiercely;
The place where humidity is too high and is easy to produce dew;
The place where exists corrosive gas or dust;
The place where vibration or impact is strong;
The place where is filled with explosive and flammable gas.
| Model |
Tank Size |
Unit Size |
Volume |
Power |
Ultrasonic Frequency |
Heating Power |
Heating |
Input Voltage |
| |
L x W x H(mm) |
L x W x H(mm) |
(L) |
(W) |
(KHz) |
(W) |
(ºC) |
(V) |
| OKS-CL002DH |
150x135x100 |
175x160x210 |
2 |
60 |
40KHZ |
50 |
05-90 |
110-240V Optional |
| OKS-CL003DH |
240x135x100 |
265x165x230 |
3 |
120 |
40KHZ |
50 |
05-90 |
110-240V Optional |
| OKS-CL0045DH |
300x150x100 |
325x180x230 |
4.5 |
180 |
40KHZ |
200 |
05-90 |
110-240V Optional |
| OKS-CL006DH |
300x150x150 |
360x180x270 |
6 |
180 |
40KHZ |
200 |
05-90 |
110-240V Optional |
| OKS-CL010DH |
300x240x150 |
330x270x310 |
10 |
240 |
40KHZ |
400 |
05-90 |
110-240V Optional |
| OKS-CL015DH |
330x300x150 |
400x325x280 |
15 |
360 |
40KHZ |
400 |
05-90 |
110-240V Optional |
| OKS-CL022DH |
500x300x150 |
580x325x280 |
20 |
480 |
40KHZ |
500 |
05-90 |
110-240V Optional |
| OKS-CL030DH |
500x300x200 |
580x325x335 |
30 |
600 |
40KHZ |
500 |
05-90 |
110-240V Optional |
| We welcome size customization, we make according to your requirements! |
|
Operation procedure
Add suitable detergent based on cleaning requirement.
Ensure correct power and switch connect before starting the equipment.
Start ultrasonic
Machine willbe in a sate of electricity after start the power switch on the back.
Mechanical model:set time, clockwise rotate the time switch to chose the tome you required between 0~30min. When the indicator light is on and make "ZIZI" sound, it shows ultrasonic works well. Please take attention that anticlockwise rotate is forbidden.
Digital model: default time is "05 00". Prss "TIME +" once to increase time by 1 minute. Press "TIME -" once to decrease time by 1 minute. Press ON/OFF after time setting and ultrasonic indicator light on. Machine works follow the setting parameter and stop work when time counts down to "00 00", then indicator light off. Please take attention that OUSR digital series with power off menory function.
Additional opeartion
Heating
Mechanical model: (with heater function model) rotate temperature control knob to adjusted temp and start heating, 40ºC-60ºC is suggested. (Heater is not suggesting for normal environment). When actual temp is lower than setting temp, heating function will auto start and the heat indicator light on. When temp reaches the setting temp, heat indicator light will off.
Digital model: Temperature display panel shows "50"and actual detergent temp. Press "TEMP+" to increase setting temperature by 1ºC,press "TEMP-" to decrease setting temperature by 1ºC. Press "ON/OFF" to start heating function and heater process, heater indicator light on, actual temperature number will blazing by 1HZ Frequency during heating process, heater indicator light will off when temperature reaches the setting temperature.
SD series model dual frequency (variable wave) function: the ultrasonic wave works intermittently in the whole wave and half wave of electric power(full wave 5seconds-stop 1 seconds-half wave 5 seconds-stop 1 seconds). It is advantageous to remove the air in the cleaning liquid, and the cleaning without dead angle is more favorable for cleaning. The function is turned on and the double frequency(variable wave) indicator light on.
SD series models fast deqi Energy: ultrasonic power only works in half of the waveform of electricity, can quickly squeeze out the air in the solution, complete ultrasonic deqi energy, power output in half. However, ultrasonic intensity is only reduced by 20. It is also suitable for the use of less power requirements.
Digital series models: if in the downtime,press the "ultrasonic switch" 3 times within 3 seconds to enter the intermittent degassing mode (work 6 seconds-stop earthquake 3 seconds-work 3 seconds-stop earthquake#timea-cycle work). Until the clock is complete.
Power off
Mechanical model: temperature control knob rotate to "OFF", heater indicate light off, disconnect the machine power. Anticlockwise rotate the timer knob is forbidden.
Digital model: Machine has stop work or press "ON/OFF"once to stop work, then disconnect machine power.
Pour out the cleaning detergent and use dry rag to clean the tank and whole unit.
Keep the shell clean.
| Trouble cleaning |
| NO |
Problems |
Possible causes |
Solutions |
Remarks |
| 1 |
No ultrasonic |
A.Power supply not connect
B.Fuse broken
C.Cable short circuit
D.Transducer short circuit
E.PCB Board broken
F.Other reasons |
A.Check and plug power switch
B.Check the fitted specification fuse
C.Connect fitted cable or replace a new
D.Inquiry our after service engineer
E.Check the Broken part and change it
F. Inquiry our after service engineer |
|
| 2 |
Time control failure |
A.Timer knob out of control
B.Timer failure |
A.Loosen or tighten the screw
B.Replace timer or digital panel
C.Inquiry our after service engineer |
Suggestion 50-60ºC |
| 3 |
No heating |
A.Heater power switch linkage
B.Fuse burn out
C.Heating pad burn out
D.Digital display board out of control
E.Other reasons |
A.Check heating plug and connect well, Check outlet line with multimeter: if OK and resistance value is few hundred O H Ms
B.Chang the same specification fuse
C.Replace the bad heating pad is open circuit
D.Check the broken part and change it
E.Inquiry our after service engineer |
|
| 4 |
Temperature control failure |
A.Thermostat loosen
B.Thermostat tube broken
C.Digital display of control |
A.Fasten the thermostat header
B.Replace thermostat
C.Check the broken part and change it
D.Inquiry our after service engineer |
|
| 5 |
Not well cleaning |
A.Not strong ultrasonic cleaning
B.Too high too low liquid surface
C.Too high too low temperature
D.Not suitable cleaning liquid
E.Other reasons |
A.Connect ultrasonic button and adjust
B.Adjust liquid into best surface
C.Adjust temperature into the most fitted
D.Stop and switch off power supply, replace suitable liquid after the previous liquid cool down
E.Inquiry our after service engineer |
Suggestion 50-60ºC |
| 6 |
Electric leakage |
A.Customer side not rounded
B.Machine not grounded |
A.To ensure grounded
B.Check if machine earth loosen |
|
Ultrasonic application description
OKS series standard ultrasonic cleaners adopt high quality stainless steel plate with strong corrosion resistance and long lifespan, transducers with advanced connection sticking technology, high electroacoustic conversion efficiency and strong ultrasonic output, also equipped with automatic constant temperature heating device. Temperature range: room temperature ~80ºC.
Suit for varies industries and objects cleaning, such as precision electronic parts, eyeglasses & clock parts, optical glass parts, hardware, jewelry, semiconductor silicon wafer, printer inkjet, medical instruments and electroplate parts etc.
| Industry |
The cleaning products and materials |
Clear dirt |
| Semi-conductor |
Integrated circuit, power ray tube, silicon wafer, diode, lead frame, capillary, tray, etc. |
Hard, etching oil, polishing wax, dust particles, etc. |
| Electrical&electronic machine |
Tube parts, cathode ray tube, printed circuit board, quartz parts, electric components,telephone switching equipment,speaker components,power meter,LCD glass, core iron parts, computer floppy disk, video parts, head, photo die mask, etc. |
Finger print, powder, cutting oil, stamping oil,iron filings, polish-ing materials, walnut powder, polishing wax, resin, dust,etc. |
| Preision machine |
Bearing, Sewing machine parts, typewriter, textile,machine, optical mechanical device, gas valve,watches cameras, metal filter |
Machine cutting oil, iron filings, olishing powder,finger print, oil, grease,drit,etc |
| Optical device |
Glasses, lens, prism, optical lens, filter lens, glass device, film, optical fiber, etc |
Plastic resin, paraffin, finger printing, etc |
| Hardware&machinery parts |
Bearing,gear, ball, metal shaft parts,tools,adjustable valve and cylinder parts, burner,compressors, hydraulic press, gun and ultracentrifuge, city water faucet, etc |
Cutting oil,iron filing, grease, polishing powder, finger printing and so on |
| Medical instrument |
Medical instrument, denture, etc |
Iron filings, Polishing powder, oil, stamping oil, dirt, etc |
| Car parts |
Galvanized parts, mold, stamping parts, etc |
Polishing scrap iron, oil, black iron shell, rust, oxidation shell, scrap iron,polishing powder, stamping oil, dirt, etc |
| Car parts |
Piston ring, carburetor, flow meter housing, compressor shell,electrical components,etc |
Iron filings, polishing powder, oil, stamping oil, dirt, etc |
| Chemical fiber |
Chemical or artificial fiber nozzle filter protector chemical fiber texture,etc |
Chemical colloid, glue, and other soild material, dust, etc. |
Ultrasonic Cleaner For Cleaning Industrial Metal Filter
Audited Supplier 
){kind=link}