Ultrasonic humidifier is an electrical appliance that can moisturize the air. It is classified into household, commercial, and industrial use according to its use.
Principle of Ultrasonic Humidifier The principle of ultrasonic humidifier is to use over-frequency oscillation (the oscillation frequency is 1.7MHz, and there are also 2.4MHz), through the use of the high-frequency resonance of the atomizer, to break the water droplets into tiny floating particles of about 5 microns. The action of the fan or stay away from the water surface in the natural state, so as to continuously produce suspended water mist, and finally achieve the effect of air humidification. Because 1.7MHz exceeds the human hearing, so the ultrasonic humidifier is derived from this. Power supply The power supply part is generally dual-input, one is for the fan, and the other is for the oscillation board. If the oscillation board and the fan voltage are the same, it can be used as one. If the power supply board uses a transformer to supply power to the oscillation circuit and the fan after stepping down, rectifying and filtering, this kind of relatively simple and simple switching power supply circuit, but the transformer is too bulky, especially for mini humidifiers It can be said to be a burden, but the design of a switching power supply circuit is sometimes a little more complicated, depending on the actual situation.
Ultrasonic industrial humidifier, no mechanical drive, no noise interference, no pollution during atomization work, high atomization efficiency, low failure rate, low energy consumption, is an efficient, reliable and practical ultrasonic industrial humidification equipment.
Description of system performance characteristics:
1. The diameter of the mist particles produced by the ultrasonic humidifier is only 1~5μm, which can be received by the air express. The humidification efficiency is close to 100%. The particles are small and uniform, and can be transported over long distances. The air is humidified without dripping. Choose the φ110mm PVC pipe To transport water mist, a single PVC pipe can transport water mist to a distance of 40-50m. No nozzles are required, so there is no trouble of blocking the nozzles.
2. The energy consumption index per unit of humidification is low, the energy consumption is only 0.05kw/(kg.w), which is equivalent to 1/10~1/15 of other humidification methods, and the operating cost is low.
3. Adopting the world's advanced atomization technology and integrated atomization components, original design to prevent fan splashing, water leakage prevention design of the mist outlet, easy cleaning design and water shortage protection device, plus the 60,000-hour high-life roller imported from Taiwan The needle bearing fan ensures excellent humidification quality and reliable performance.
4. When the humidifier is atomized, there is no mechanical drive, no high-power motor, not pure mechanical energy to drive humidification, no compressed air, no noise interference, no pollution. The failure rate is low, it is an energy-saving and environmentally friendly humidification equipment, which is efficient, reliable and practical, and is your ideal choice.
5. The model is small in size, and can be independently built into a system according to site conditions. It is not only suitable for the installation of new plants, but also can transform and upgrade the old plants without destroying the original equipment to meet the humidity requirements of the production process.
Precautions for use:
1. When the atomizer is working normally, please do not put your hands on the spray cavity of the atomizer to prevent ultrasonic damage.
2. The atomizer must be in water to work normally, please put it in the water before turning on the power, and make sure that the surface of the atomizer is in a state of water to avoid damage to the atomizer.
3. When you stop using the atomizer, please disconnect the power first, and then take out the atomizer from the water.
4. When using this atomizer, please select the output power greater than 350W and the output voltage is DC48 power supply. The power supply should be isolated from the fog to avoid the fog from getting into the power circuit board, short-circuiting, and burning the power supply.
5. When multiple atomizers are used in the same container, they need to be equipped with separate power supplies. It is not possible to connect multiple atomizers with a single power supply for use, and pay attention to make the shells of each atomizer communicate with each other to prevent it from working. Electric corrosion.
6. The mist produced by the atomizer must be forced out by a fan, and each group of atomizers retain a 350cm2 plane space to avoid excessive water temperature and shorten the life of the atomizer.
7. The atomizer is not suitable for atomizing corrosive liquids, so as not to damage the metal shell and atomizing film of the atomizer.
8. Please don't damage the water level sensor switch during installation, so as to avoid the failure of the water level switch and cause the atomizer to lose control. If the water level switch is damaged, stop using it, otherwise the atomizer will burn dry and further damage the atomizer. At this time, it can be used after being repaired by professional maintenance personnel.
Audited Supplier 
){kind=link}